- Mtsx labtool r03.00.02 serial#
- Mtsx labtool r03.00.02 update#
- Mtsx labtool r03.00.02 manual#
- Mtsx labtool r03.00.02 full#
- Mtsx labtool r03.00.02 code#
there is no way of going back to a "normal".you will not be able to clone this radio to any.you will not be able to program any old saved.Your radio, it becomes an individual radio once you create your own model profile and program.NOTE:There are a couple of things you should be aware of before you undertake this project: The problem is getting the radio to do it. It appears that all A7 model MT2000's are capaple of doing 255 modes rather than the 160 they are shipped with. This may be a little too scary for some of you to want to attempt but. MDC1200 h/w decoder disabled in codeplug, Old SLIC IC version Incompatible trunking s/w and h/wTrunking h/w decoder disabled in codeplug, Old SLIC IC version Selected Mode (Zone/Channel) codeplug checksum error Operational Display Codes: 14 CHAR FAILURE DISPLAYīad frequency data in codeplug, defective synthesizer Power-up Display Codes: 14 CHAR FAILURE DISPLAYīad external codeplug data, Defective external EEPROMīad internal codeplug data, Defective microcontroller 6881072C40 - MTX8000/9000 B5/B7 Operator's Manualīelow is a list of the Power-up Display Codes and Operational Display Codes that may show up on your MTSX series radio.
Mtsx labtool r03.00.02 manual#
Here are a listing of the Service Manual part numbers for this series of radios: You need the control box (with or without integrated power amplifier) that interfaces to the DB25, otherwise that's all you have is a radio holder. NOTE: The NTN1340A is NOT a complete MVA if you only have the radio holder portion. Pinouts as they are in the holder unit schematic diagram for the NTN1340A:Ĭonnector J104 goes to the Battery Board it's a 10 pin connector, pins are:
The pinout of the 6pin power connector on the NTN1340A is:Īccording to the manual the top row is 4 5 6 left to right with a square over pin 5. For HMN4044, HMN4047, NMN6209, and NMN6210 microphones, set both dip switches toward the back of the holder.
Mtsx labtool r03.00.02 serial#
These are used to select whether the microphone you are using has a manual PTT or serial data PTT.įor HMN1035 and HMN1056 microphones, set both dip switches toward the front of the holder. If you have the MTSX Convertacom (MTVA), you will notice that there are two DIP switches located on the bottom rear corner of the MTVA holder. MTVA Vehicular Adapter Instruction Manual 6881075C95. The individual part numbers for the components of this cable are listed below. This is the actual Motorola cable used for programming and servicing these radios. You may want to look at the schematic for the RKN4035D Service Cable. The cable you need is the standard MTSX programming cable.ĭo you want to build your own programming cable? If you don't want to use an old speaker mic cable, see the individual part numbers of the parts for the Service Cable, below.
Mtsx labtool r03.00.02 update#
Now, the update for this software is RVN4097M R06.00.00 05 Sept 97, which should mean that it should program the radio as well. The RVN4097F ver R02.10.01 RSS package specifically shows it programs the following radios: MT/MTS2000 MTX838/8000/9000. If you are trying to program a MTX-838, from what we've heard, you need to use the MTSX software. If you are using a Public Safety speaker mic with the radio, you might want to order part number 3205514W01 to cover the antenna connector on the radio. If you have the accessory adapter for the side connector on the radio, the typical schematic of the speaker mic looks like this. You set SYSTEMWATCH to the Spectra with RIB mode (works best). The radio DOES NOT have to be programed to the system you want to watch. NOTE: When the radio is in the RF MODEM mode, it will do a self test and then the screen will go blank. You can put the radio into RF modem mode from the F4-F4-F4 (Trunking Config).
Most MTS2000/MTX8000's only have a 256k controller, which will not work. Firmware version has to be above 5.44 (which has a 512k controller in it). You can run system watch using a MTS2000 handheld.
Mtsx labtool r03.00.02 code#
However, you can clone a Type II code plug into a B3 radio and it will work just fine. There were a few B3's that were Type II produced by Motorola.
Mtsx labtool r03.00.02 full#
If it is an MTX8000 and has a front mounted display with either a 6 button or full keypad, you have a radio that will do Type II. If you are (un)lucky enough you might find an F3 modem that does Type II. You can view this bulletinīoth the MTX8000 B5 & B7 models are Type II Trunking. Have a look at the MTSX series model breakdownĪ manual supplement has been released for the MT2000/MTS2000/MTX838 with a newĪlignment procedure for the front end pre-selector. Upgrading your MT2000 from 160 to 255 modesĬhanging band limits in all MTSX RSS versions
0 kommentar(er)
